您好!欢迎访问东莞市索想电子有限公司!
English
中文版
全国服务热线
RS16系列规格书
RS16 SERIES SPECIFICATION
1.一般事项General
1-1.适用规格Scope
本规格书适用于RS16型开关。
This specification applies to RS16mm size switch
1-2.标准状态Standard atmospheric conditions
    除另有规定外,测量应在以下状态下进行:
    Unless otherwise specified ,the standard range of atmospheric conditions for making
    measurements and test is as following limits:
   温    度 Ambient temperature : 15℃ to 35℃
   相对湿度 Relative humidity   : 25% to 85%
   气    压 Air pressure       :86kpa to 106kpa
   如果对在上述所提到的条件中所做的实测值有疑问的话,应使用以下条件进行测量:
   If doubt arises on the decision based on the measured values under the above-mentioned
   Conditions ,the following conditions shall be employed:
   温    度 Ambient temperature : 20±1℃
   相对湿度 Relative humidity   : 63% to 67%
  气 压 Air pressure       :86kpa to 106kpa
1-3.使用温度范围
   Operating temperature range  : -21℃ to +70℃
1-4.保存温度范围
   Storage temperature range    : -30℃ to +80℃
2.构造Construction
2-1.尺寸Dimensions
    见所附成品图Refer to attached drawing
3.额定值Rating
3-1.额定电压
   Rated voltage :DC 16V
3-2.最大额定电流(阻抗负载)
   Maximum operating current (resistive load) 0.3A
4.电气性能Electrical Characteristics
项目
ITEM
条件
CONDITIONS
规格
SPECIFICATIONS
4-1.开关电路接入点数
Switch circuit and
Number of pulse
详见所附成品图
Refer to attached drawing 
极数Poles段数Sections
18
4-2.绝缘阻抗
Insulation
resistance
在端子和支架间施加电压500V DC 1分钟。
Measurement shall be made under the condition
which a voltage of 500V DC 1 min is applied between
individual terminals and frame
100MΩ 以上
100MΩ Min
 4-3.耐电压
Dielectric
strength
在端子和支架间施加电压AC1300V 电压1分钟
A voltage of 1300V AC shall be applied for
1 minute between individual terminals and frame 
不得有绝缘破坏
Without arcing or breakdown
4-4.端子间接触阻抗
Contact resistance
出力信号处于ON时安定状态条件下测定
Measurement shall be stable condition which a
Output signal is ON
寿命前:50mΩ 以下
寿命后:1Ω以下
5. 机械性能 Mechanical Characteristics
 5-1.转换角度
Changeover angle

45°±3°(one-step operating angle)
5-2.旋转力矩
Rotational torque

250±100gf.cm)
  5-3.轴的推拉强度
Push-pull
Strength of shaft
在轴端,沿轴向施加10Kg的静负荷力推和拉各10秒钟(产品焊锡固定在PCB上.)
Push and pull static load of 8Kg shall be applied to the shaft in the axial direction for 10s.
(After soldering of the PCB board)
轴向虚位间隙0.4以内
Shaft play in axial
direction 0.4 Max
 5-4.端子强度
Terminal
strength
在端子的先端施加5N(500gf)的力1分钟.
A static load 5N(500gf) be applied to the tip of
terminals for 1 minute in any direction.
端子无损坏,无过度的松度,允许变形.
Without damage or excessive
looseness of terminals. Terminal
bend is permitted.
5-5.轴套螺纹紧固强度
Bushing Nut
Tighten Strength

7.0Kgf.cm 以上
7.0Kgf.cm Min
5-6.止动强度
End stop strength 


5-7.轴向间隙
Shaft play in axial
direction  

0.4mm以下
0.4mm Max
5-8.轴摆动
Shaft wobble
在距离轴顶端5MM处,沿径向瞬间施
加50mN.m(500gf.cm)的力测试
A momentary load of 500gf.cm should be applied at the point 5mm from the tip of the shaft in a direction
perpendicular to the axis of shaft.
0.7*L/30mm p-p以下(L:指安装平面到轴的柄端的距离.)
0.7*L/30mm p-p Max
L :Distance between mounting surface
and measuring point on the shaft
5-9.轴的回转方向摆动
Shaft play
in rotational wobble
用角度板测定.
Testing by angle board.
5°以下
5°Max
6. 耐久性能Endurance Characteristics
项目
ITEM
条件
CONDITIONS
规格
SPECIFICATIONS
6-1.回转寿命
Rotational life
在无负荷条件下轴以600~800周/小时速度回转,
24小时连续5000~8000次.
The shaft of switch shall be rotated at speed of 600~1000
cycles /H without electrical load, after with
measurements shall be made
(5000 to 8000 continuous cycles for 24 hours.)
10000±200周
10000±200 cycles per below 100gf.cm
尚余有轻微定位感.
端子间接触阻抗1Ω以下
Detent feeling has to remains
Contact resistance 1Ω Max
6-2.耐湿性
Damp heat
温度40±2℃,湿度90~95%的恒温恒湿槽中放置
96±4小时后,在常温、常湿中放置1.5小时后测试.
The switch shall be stored at temperature of 40±2℃
with relative humidity of 90~95% for 96±4
in a thermostatic chamber. And the switch shall
be subjected to standard atmospheric conditions
for 1.5H, After which measurements shall be made.
所有项应满足初期规格
Specifications in clause
All items is shall be satisfied
6-3.耐热性
Dry heat
温度80±3℃,的恒温箱中放置96±4小时,常温、常湿放置1.5小时后测试.
The switch shall be stored at a temperature of 80±3℃ for 96±4H in a thermostatic chamber, And then the switch . Shall be subjected to standard atmospheric conditions for 1.5H, After which measurements shall be made.
所有项应满足初期规格.
Specifications in clause all items
is shall be satisfied
6-4.低温特性
Cold
温度-40±3℃的恒温箱中放置96±4小时,常温、常湿放置1.5小时后测试.
The switch shall be stored at a temperature of -40±3℃ for 96±4H in a thermostatic chamber, And then the switch . Shall be subjected to standard atmospheric conditions for 1.5H, After which measurements shall be made.
所有项应满足初期规格.
Specifications in clause all items
is shall be satisfied
6-5.焊锡耐热性
Resistance
to soldering heat
槽焊Dip soldering .
使用基板:t=1.6mm的单面覆铜板.
Printed wiring board :single-sided copper clad
laminate board with thickness of 1.6mm.
预热:基板表面温度100℃以下,时间1分钟以内.
Preheating:1.Surface temperature of board:100℃ or
less 2.Preheating time :within 1 minute
焊接:温度260±5℃或以下,时间3秒以内.
Soldering :solder temperature: 260±5℃ or less
Immersion time :within 3S
手焊 Manual soldering
温度350℃以下,时间3秒以内.
Bit temperature of soldering iron:350℃ less than
Application time of soldering iron :within 3S
不得有绝缘体的破损、变形、
接触无异常
Electrical characteristics
shall be satisfied No
mechanical abnormality
6-6.盐雾试验
Salt mist
无明显锈迹,无变色                         No apparent rust and discoloration在温度为35±2℃,浓度(重量比)为5±1%的条件下,进行8小时连续喷雾后取出水洗.       Test should be made with temperature of 35±2℃ and concentration of 5±1% (by weight) for 8 h. Then clean with wate
6-6.焊锡性
Solderability
端子在260℃±5℃的温度的焊锡槽内浸锡3秒±0.5秒.
The terminals shall be immersed into solder bath
at 260℃ for 3S±0.5S.
浸渍面须有75%以上焊锡附着
A new uniform coating of solder
shall cover 75% minimum of the
surface being immersed 
7. 包装部分 Packing Portion
项目
ITEM
条件
CONDITIONS
规格
SPECIFICATIONS
7-1.包装方式
Packing
使用吸塑盒和纸箱包装Use plastic box and carton packaging.每盒100PCS,每箱10盒
共计:1000PCS/箱
Put 100PCS products into foamed
plastic plate, then pack 10plates
into a carton, total 1000PCS/carton


如您对我们的产品感兴趣或有任何的疑问,请及时与我们联系!
地 址:东莞市茶山镇塘角村塘中路东海工业大厦
电 话:0769-89156858-815/819
手    机:18666440282 18676913668
邮 箱:xuqian@suo-xiang.com
网 址:http://www.suo-xiang.com

Follow Us On

TWITTER
东莞市索想电子有限公司 【技术支持】 Power by DedeCms 版权所有 网站地图
  *本站相关网页素材及相关资源均来源互联网,如有侵权请速告知,我们将会在24小时内删除* 技术支持:东莞广为文化传播有限公司后台管理